Dacromet coatings with different mass fraction of Al were prepared with zinc and aluminum flakes as raw materials,and the corrosion resistance of the coatings was evaluated and investigated by using salt spray test and electrochemical methods.
以片狀鋅粉和片狀鋁粉為原材料制備不同鋁的質量分?jǐn)?shù)的達克羅涂層。
To improve properties of dacromet coatings, a mixture process of metal powders was adopted in the preparation of dacromet solutions.
為提高達克羅涂層的性能,在制備達克羅涂液時,對金屬粉進行混合工藝處理。
Classification and composition of dacromet solutions were described, characters of dacromet process and properties of dacromet coatings were described as well.
達克羅涂層由于具有優良的耐蝕性、無氫脆、無污染等特點而得到廣泛應用。
The Study of Dacromet's Microstructure and Its Electrochemical Characteristics;
達克羅涂層的組織結構及電化學特性研究
Dacromet was compared with electrogalvanized and hot galvanized deposits in adhesion, hydrogen embrittlement, weatherability, heat and corrosion resistance.
闡述了達克羅涂層的組成、結構及制作過程。
Discussion of Double Raceway Dynamic Grinding Method on Top Roller Bearing Out Ring
上羅拉軸承外圈雙滾道動態磨削方法的探討
Calculation is done of the radial clearance of the top roller bearing SL1-6918 to determine the clearance range.
對SL1-6819型上羅拉軸承進行了徑向游隙的計算,以便確定游隙的范圍;分析了上羅拉軸承的結構和上羅拉軸承的游隙在實際使用狀況下的存在形式及對軸承運轉的重要作用;提出了影響成紗質量的關鍵因素。
Discussion of Double Raceway Dynamic Grinding Method on Top Roller Bearing Out Ring
上羅拉軸承外圈雙滾道動態磨削方法的探討
Impact Analysis of the Ring Slot around the Bearing Shell of Top Rollers on Cot Telescoping Process
上羅拉軸承外殼環形槽對套制膠輥的影響分析
Application of Self-lubricating Roller Bearing in Spinning Frame
含油自潤滑羅拉軸承在細紗機上的應用
Provide manufacture services of rubber-ware pressing process machine, roller bearing oiling, rubber-ware grinding and cutting.
提供皮棍壓套羅拉軸承加油皮棍磨削加工服務。
upper center crankshaft bearing
曲軸主軸承上中軸瓦
Remove the lower insert from the bearing cap.
從軸承蓋上拆去下軸瓦。
The journal rubs against the bearing surface.
軸頸在軸承面上摩擦。
Remove thrust bearings from rear main bearing carrier.
從后主軸承托架上拆下止推軸承。
Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.
曲軸上的導向軸承:曲軸上的導向軸承一般或者是軸瓦,或者是球軸承。
Excessive friction in strut upper bearing
支柱上軸承磨損過度
governor upper bush
調速器上部軸承襯套
radial bearing upper drive sub
上部徑向軸承傳動接頭
The carriage is supported on guide shafts.
托架支承在導軸上。
Schromberg alloy
施羅姆伯格鋅基軸承合金
Pull vibration damper off of the crankshaft.
將減震器從曲軸上拉下。
Drawing of Cold Stamping Process of Bearing Frame and Die Design
軸承架的冷沖壓拉深工藝及模具設計
Shaft Assembly (Male, female, washer, grease….
軸組件（軸，軸套，軸承，油脂。。。）
RUGGEDNESS. Automotive ring gear differential. Axle shafts on roller bearings.
強度：自動差速齒輪，滾子軸承上的剛性車軸。